[plug] DMESG Output
Daniel Pearson
daniel at flashware.net
Tue Jun 27 23:31:43 WST 2006
Ok, I grabbed the package from backports and dpkg'd that and its now
installed.
The output of smartctl --all /dev/hda is:
smartctl version 5.36 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6
Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST3200827A
Serial Number: 4ND3FTYA
Firmware Version: 3.AAH
User Capacity: 200,049,647,616 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Jun 27 23:26:38 2006 WST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 25) The self-test routine was
aborted by
the host.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 70) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 108 099 006 Pre-fail
Always - 143754591
3 Spin_Up_Time 0x0003 100 099 000 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age
Always - 12
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 065 060 030 Pre-fail
Always - 3188788
9 Power_On_Hours 0x0032 100 100 000 Old_age
Always - 166
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age
Always - 16
187 Unknown_Attribute 0x0032 100 100 000 Old_age
Always - 0
189 Unknown_Attribute 0x003a 100 100 000 Old_age
Always - 0
190 Unknown_Attribute 0x0022 066 064 045 Old_age
Always - 589299746
194 Temperature_Celsius 0x0022 034 040 000 Old_age
Always - 34 (Lifetime Min/Max 0/13)
195 Hardware_ECC_Recovered 0x001a 054 048 000 Old_age
Always - 150532189
197 Current_Pending_Sector 0x0012 100 100 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age
Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age
Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age
Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Extended offline Aborted by host 90%
166 -
# 2 Extended offline Aborted by host 90%
166 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
*Daniel Pearson
*Flashware Solutions ABN 58 438 456 919
Mob: 0438 118 897 | Email: daniel at flashware.net
<mailto:daniel at flashware.net>
The information contained in this electronic transmission is
confidential. If you are not the intended recipient of this
transmission, use of this information is strictly prohibited. If you
have received this transmission in error, please contact Flashware
Solutions 0438 118 897.
Craig Foster wrote:
>> -----Original Message-----
>> From: plug-bounces at plug.org.au
>> [mailto:plug-bounces at plug.org.au] On Behalf Of Daniel Pearson
>> Sent: Tuesday, 27 June 2006 10:23 PM
>> To: plug at plug.org.au
>> Subject: [plug] DMESG Output
>>
>> Hi Guys,
>>
>> Have been having a look through my dmesg and I get the following:
>> [285227.084587] hda: dma_timer_expiry: dma status == 0x21
>> [285237.076070] hda: DMA timeout error [285237.082256] hda:
>> dma timeout error: status=0x58 { DriveReady SeekComplete
>> DataRequest } [285237.096202] ide: failed opcode was: unknown
>> [285237.134045] hda: status error: status=0x50 { DriveReady
>> SeekComplete } [285237.141990] ide: failed opcode was:
>> unknown [285237.149855] hda: no DRQ after issuing
>> MULTWRITE_EXT [285237.262284] hda: status timeout:
>> status=0xd0 { Busy } [285237.270447] ide: failed opcode was:
>> unknown [285237.278920] hda: no DRQ after issuing
>> MULTWRITE_EXT [285237.325854] ide0: reset: success
>> [285257.318815] hda: dma_timer_expiry: dma status == 0x21
>>
> <snip>
>
>> Having a google doesn't really provide a whole heap of info,
>> its a new drive (200gb Seagate). Has anyone come across this
>> before? Running kernel 2.6.15-23-amd64-server - distro is
>> Ubuntu-server
>>
>> Cheers
>>
>> --
>>
>> Daniel Pearson
>> Flashware Solutions ABN 58 438 456 919
>> Mob: 0438 118 897 | Email: daniel at flashware.net
>> <mailto:daniel at flashware.net>
>>
> <snip>
>
> Three issues I've seen...
>
> 1) IDE cables.
> Swap and try again
> 2) DMA set too high
> Seagates seem to suffer the most for me... ***Cautiously test***
> the DMA settings, Multiword, and transfer speed settings on hdparm.
> 3) Drive failure
> smartctl is your friend... It will query the drive to see if the
> drive reports having difficulties... What most hard drive testing utils
> do.
> Download the bootable CD from seagate to test the drive. It runs
> linux, so it should be pretty on the ball.
>
> HTH
>
> CraigF.
> _______________________________________________
> PLUG discussion list: plug at plug.org.au
> http://www.plug.org.au/mailman/listinfo/plug
> Committee e-mail: committee at plug.linux.org.au
>
>
More information about the plug
mailing list